[. . . ] Even the slightest touch of any of these parts to a power line can cause electrocution and death. If any part of the antenna system should come in contact with a power line, don't touch it or try to remove it yourself. [. . . ] com/welcome.
EN
5
English
What's in your box
1 2 3 4
1x
5 6
1x
7
1x
8
1x
2x
9 10 11
2x
12
4x
13
4x
1x
14
1x
4x
1x
1x
a SDV8622/12 antenna b Power supply 100-240V AC / 6V DC 500mA c Wall/Mast bracket d Nut e U-Bolts f Mast clamps g Nuts with lock washers h 25mm wood screws i 6m coax cable with connectors j Weather boot k Power injector l Plastic anchors m Washer n 40mm Hexagon screw
6
EN
Installation
Installation information
This antenna uses a power inserter module to powertheantennaamplifier. It is essential for proper operation of this antenna system that the power inserter be connected between the antenna and any devices such as splitters, matching transformers, networks, etc.
Note · Indoor, choose a location near a window
which gives the antenna a clear view of the transmitter.
Note · Place the antenna away from metal surface to
avoid interference.
a
For indoor wall mount installation
Note
b c d
· Complete all assembly work on the ground
before installing on a wall or an antenna mast.
1
Use the nut , washer , and hexagon screw to attach the antenna to the wall/mast bracket.
a b c d
Antennawithbuilt-inamplifier Power inserter module Splitters or matching transformers (not included) TV or video device
EN
7
English
3 Get started
Determine the signal strength
Before Installation, determine the best location for optimum reception. It is important for the antenna to have an unobstructed path to the transmitter. For best results, ensure the antenna faces the location of the transmitter.
2
Use the screw holes of the wall/mast bracket as a guide to mark position for the wood screws.
For outdoor mast mount installation
Note · Complete all assembly work on the ground.
Raise the completed antenna after assembly.
1
Use the nut , washer , and hexagon screw to attach the antenna to the wall/mast bracket.
3
Use the wood screws tofixthe antennatothewoodwallfirmly.
3. 2mm (1/8") 27±5mm 1. 1"±0. 2"
2
Insert U-bolts into the holes of the wall/mast bracket . Attach the four nuts with lock washers to the U-bolts .
7. 9mm (5/16") 35±5mm 1. 4"±0. 2"
8
EN
3
Attachtheassemblytothemastfirmly.
Rotate
English
You can make a 90 degree rotation to the antenna or the mounting post.
4 5
Rotate the mast in its mount to adjust the direction. Attach the coaxial cable to the F connector on the underside of the unit. Position the weather boot over the connection.
EN
9
Warning · The power injector and power supply are for
indoor use only.
Tip · This antenna includes a 6m roll of 3C-2V
coaxial cable. If this is not adequate for your needs, replace the cable with a RG-6 coaxial cable instead of adding an extension.
Set up a digital tuner with this antenna Connect to the TV
Note · Aspreviouslynoted, theamplifier(Power
injector + Power supply) must be placed inline between the antenna and any splitter or additional devices.
You can install available channels with the digital TV tuner. Ensure the antenna has set up properly before the tuner can receive viewable channels. There are two ways to connect the antenna to the TV: · Connect the antenna to a digital tuner. [. . . ] Yes, this antenna can be set up with a digital tuner (see the section on "Set up a digital tuner with this antenna").
EN
11
English
6 Glossary
A
Amplifier A device, either a single stage or a large scale circuit with multiple stages for creating gain, i. e. Antenna A device, such as a rod or wire, which picks up a received radio frequency signal or radiates a transmitted RF signal.
televisionsystems(standard-definitionTV, or SDTV). [. . . ]